Mama's Must-Haves

Articles · Cleaning

How to clean bath toys and stop mold

Some links here are affiliate links. If you buy through one, I earn a small commission and your price stays the same. How that works.

A yellow rubber duck in a white bathtub

To clean bath toys, soak them in a mix of equal parts white vinegar and warm water for an hour, scrub, rinse, and let them dry all the way. To stop mold, squeeze the water out after every bath and store the toys where air can reach them. The best fix is to swap squirt toys with holes for toys that are sealed or open up to clean.

If you have ever squeezed a rubber duck and watched black specks shoot out, you know the problem. Water gets inside, never dries, and mold grows. It is gross, but it is fixable.

Why bath toys get moldy

Mold needs water, warmth, and something to feed on. A bath toy with a hole has all three. Water and soap scum get sucked in. The inside never dries. Mold grows where you cannot see it.

Toys without holes still get a film of soap scum. That can grow mildew too if the toys sit wet in a basket.

What you need

  • White vinegar
  • A bucket or the sink
  • A bottle brush or old toothbrush
  • Pipe cleaners, for small holes
  • Dish soap
  • A mesh bath toy bag or a drying rack
  • Hot glue, if you want to seal holes for good

Shop it: distilled white vinegar, a small bottle brush set, a mesh bath toy organizer, or a bath toy drying rack.

How to clean bath toys with vinegar

1. Mix the soak. Fill a bucket or sink with equal parts white vinegar and warm water.

2. Fill and squeeze. Drop the toys in. Squeeze each toy with a hole so it sucks up the vinegar water. Squeeze it out and repeat a few times.

3. Soak for an hour. Let the toys sit in the mix.

4. Scrub. Use a brush on the outside. Push a pipe cleaner or small brush into any hole you can reach.

5. Rinse. Squeeze clean water in and out of the toys until it runs clear.

6. Dry all the way. Squeeze out as much water as you can. Set the toys on a towel or rack in a spot with air flow. Turn the toys with holes upside down. Let them dry for a full day before they go back in the bath.

Do this once a week, or every few weeks if you squeeze and dry them after each bath.

How to clean bath toys with bleach

For toys with visible mold, a diluted bleach soak works. Use regular unscented household bleach.

1. Mix the bleach and water. Follow the dilution directions on your bleach label for cleaning hard surfaces.

2. Soak. Fill and squeeze the toys so the mix gets inside. Soak for the time on the label.

3. Rinse well. Squeeze clean water in and out many times. Rinse until you cannot smell bleach.

4. Dry all the way. Same as above.

Never mix bleach with vinegar or any other cleaner. The mix can release harmful fumes. Use one method at a time, and rinse well between them. Wear gloves and open a window.

Can bath toys go in the dishwasher?

Some can. Check the toy’s label or the maker’s website. Hard plastic toys without holes often do well on the top rack. Skip it for soft rubber toys, toys with electronics, and anything with paint or stickers.

When to throw a toy away

If you squeeze a toy and black bits keep coming out after cleaning, toss it. Some mold is too deep inside to reach. A bath toy is cheap. It is not worth the fight.

How to stop mold for good

Squeeze and dry after every bath. Squeeze each toy until no water comes out. Store them in a mesh bag or on a rack, not in a closed bin.

Seal the holes. Before a new squirt toy goes in the bath, plug the hole with a dab of hot glue. It stops being a squirt toy, but it will not grow mold inside.

Buy toys with no holes. Many brands now sell bath toys with no holes, or toys that come apart so you can clean inside. These are the ones I would buy.

Rotate. Keep a small set in the tub and the rest dry in a closet. Swap them every week or two.

Shop it: mold-free bath toys, bath toys that open to clean, or a mesh bath toy organizer.

Bath toys I would buy

  • Stacking cups. No holes, and they last for years.
  • Bath crayons. They wash off the tub and do not hold water.
  • Toys that pull apart into two halves for cleaning.
  • Foam letters, as long as you let them dry flat on the tub wall.

I put mold-free squirt toys in my list of stocking stuffers for toddlers that get used for this reason.

What not to do

  • Do not store toys in a closed bin or a bucket with no holes.
  • Do not mix bleach with vinegar or other cleaners.
  • Do not leave toys sitting in a puddle on the tub ledge.
  • Do not keep a toy that still sheds black bits after cleaning.

More cleaning help

For other kid gear, see my guides on how to wash stuffed animals and how to clean seat belts. My house cleaning tips cover the rest of the house. If you are shopping for a baby tub, my post on the best baby bathtubs can help.

Questions parents ask

How often should you clean bath toys?

A vinegar soak once a week is a good habit. Squeeze out the water and let the toys dry after every bath.

Is mold in bath toys dangerous?

Mold is not something you want in your child’s bath water or mouth. Clean or toss moldy toys. If your child has allergies, asthma, or you are worried about a reaction, call your doctor.

Can you put rubber ducks in the dishwasher?

It depends on the duck. Many soft rubber toys warp or trap water. Check the maker’s care directions first.

How do you get mold out of a squirt toy?

Soak it in vinegar water or a diluted bleach solution, squeezing it full many times. Rinse well. If black bits still come out, throw it away and seal the hole on the next one with hot glue.